42x PCI Carrament grey middle bed and joint mortar 25kg

Palette 42 sacks each 25kg PCI Carrament gray at an unbeatable price

MHD 032025 Goods from return and warranty exclusion

PCI Mittelbett- und Ansetzmörtel für Naturstein und Feinsteinzeugbeläge

Product Properties

• Plastic, flexible laying mortar, the Mittelbettmörtel is only distributed with a sufficiently large notched trowel (Mittelbettkelle)
• Deformation-capable, compensates temperature fluctuations and substrate stresses
• Adheres without priming or priming on concrete, cement screed, and cement plaster
• Effective crystalline water binding, therefore especially suitable for large-format ceramic tiles
• Low shrinkage, even with thick mortar layers up to 4 cm, no shrinkage stresses between PCI Carrament and natural stone tiles
• Durably water-resistant and frost-proof, suitable for interior and exterior use on walls and floors
• Quick setting, reduces absorption of the laid material during processing, preventing efflorescence
• Quickly hardening, walkable and grouting after approximately 6 hours, fully loadable after about 1 day
• In white, no show-through of the adhesive bed with white marble when laid using the combined buttering-floating method
• PCI Carrament meets classification C2F according to DIN EN 12004
• EMICODE EC 1 PLUS R

Color: gray

Delivery form: 25kg sack

Application Area

• For interior and exterior use
• For wall and floor applications
• For laying natural stone tiles, including sheet material
• For large-format porcelain stoneware tiles
• For leveling uneven substrates prior to laying
• PCI Carrament gray also for laying sewer pipe bricks in wastewater structures
• For stairs and house sills in residential areas on electric underfloor heating, heated screeds, balconies, and terraces in halls, rooms, and on openings of industrial buildings, institutions, service, and administrative buildings

Substrate Preparation

• Minimum substrate age: PCI Novoment Z1 or PCI Novoment M1plus screed 24 hours
• PCI Novoment Z3 or PCI Novoment M3plus screed 3 days
• Cement screed 28 days
• Concrete 3 months

The substrate must be dry, dust-free, and load-bearing. Highly absorbent cement substrates should be primed with PCI Gisogrund 1 diluted with water. For abraded anhydrite or gypsum, liquid screeds, and cast asphalt screeds indoors, use undiluted PCI Gisogrund. For time-sensitive work, cementitious and gypsum-containing substrates should be primed with PCI Gisogrund Rapid. Allow primer to dry. Screeds must not exceed 4% residual moisture for cement screeds and 0.5% for anhydrite screeds.

Application of PCI Carrament

Pour the mixing water into a clean working container. Add PCI Carrament and mix with a suitable stirring or mixing tool attached to a drill to form a homogeneous, lump-free mortar. After a reactivity time of approximately 3 minutes, briefly remix.

Laying Natural Stone Tiles

Apply PCI Carrament section-wise to the substrate. Draw a contact layer. Using a Mittelbettkelle or another suitable notched trowel that allows for a largely full bedding, spread as much mortar as can be covered with natural stone within the open time. Check the open time with a finger test. Lay the tiles with a slight sliding motion to achieve a largely full bedding.

Adhesive Method

PCI Carrament can also be used for setting large-format natural stone tiles on walls, such as stair risers or sills. Apply PCI Carrament in the desired thickness to both the substrate and the back of the tiles using a Mittelbettkelle or spatula. Press the natural stone tile into place, align, and wedge if necessary. Ensure only as much mortar is applied as can be covered with tiles within the open time. Check the open time with a finger test. Applying PCI Carrament to the back of the tiles prevents show-through of the adhesive joints and allows for a largely hollow-space-free installation.

Grouting

For joint widths from 1 to 8 mm

Special Cases

For plastic jointing of polished natural stones, PCI Flexfug from 2 to 10 mm joint width (except color tone sand gray 3 to 15 mm). PCI Rapidfug from 1 to 10 mm joint width.

For non-sensitive natural stones, consulting PCI is recommended. Other PCI joint mortars may also be used for joint widths from 2 to 8 mm, such as PCI FT Fugengrau or PCI FT Fugenweiß from 5 to 20 mm.

Elastic Joints

Corner joints, floor-wall, wall-wall, wall-ceiling, and connection joints, as well as for installation parts, tile coverings, wood coverings, elastic with PCI Carraferm.

Safety Data Sheet

Safety Data Sheet
Label	Datenblatt
Sicherheitsdatenblatt PDF
Revised by supplier on	12092016
Work Safety and Storage
Hazard symbols	H315 Causes skin irritation H318 Causes serious eye damage
Precautionary statements	P102 Keep out of reach of children P264 Wash thoroughly after use P280 Wear protective gloves, protective clothing, eye protection, face protection
First aid measures	P301+P352 IF ON SKIN: Wash with plenty of soap and water P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. P315 Get immediate medical advice P332+P313 If skin irritation occurs, seek medical advice
Storage Classes
Class	Non-combustible solid
Water hazard class	Water hazard class 1, slightly water hazardous
Hazard
Signal word	Danger
GHS Pictogram
Contents
CAS Number Basis for classification Substance name 65997-15-1