<li>webertec Superflex D2 Sealant 24kg</li> <li>weberprim 801 Primer 1l</li>

webertec Superflex D2 Flexnbsp;Sealing Slurry 2knbsp;24kg weberprim 801 Primer 1L

Attention: Before applying Superflex D2, the substrate must be primed with weberprim 801. weberprim 801 should be diluted undiluted with water in a ratio of up to 1:1 RT. After drying, the scratch coat is applied, followed by the coating.

Highly flexible, reactive, and fast-setting sealing slurry

Application area:
For flexible sealing of basement exterior walls, plinths, and foundations wall/floor For subsequent interior sealing Negative sealing For sealing containers indoors up to 10 m water column As a primer and adhesion bridge under PMBC, to create horizontal barriers in and under rising walls, and as an adhesion bridge on existing bitumen coatings For sealing in conjunction with ceramic coverings, e.g., swimming pools/moisture/wet rooms

Product description:
webertec Superflex D 2 is a two-component, fast-curing flexible slurry with general building authority approvals MDS according to DIN 18533

Composition:
Cement, selected quartz sands, highly reactive polymers, reactive fillers, additives

Product features:

• Fast-curing
• Reworkable after 90 minutes in wall areas
• Walkable after 4 hours, tileable
• Weather-independent drying within 24 hours
• Dry residue > 95%
• Crack bridging > 1 mm
• Suitable for all mineral substrates, no plaster layer required on masonry
• Can be plastered, painted, frost/ice resistant, UV resistant
• Durably water-resistant after 3 days
• Sprayable with peristaltic pump technology and screw pump technology, e.g., Wagner PC 1030 with air support

Application temperature: 3 °C to 30 °C air and object temperature
Density: approx. 1.05 kg/dm³ of the finished mixture
Consistency: slurry, brushable, trowelable, sprayable
Processing time: approx. 45 min
Cleaning: with water while fresh
Tools: trowel, float, roller, spray equipment
Color: gray
Drying time: approx. 24 hours
Storage: In a dry, frost-free environment in the original sealed container, the material remains usable for at least 12 months

Consumption / Yield:

weberprim 801 Primer for absorbent substrates 1L

Ready-to-use primer for pre-treatment of absorbent substrates

Application area:

• For highly absorbent substrates
• For interior and exterior
• For wall and floor

Product features:

• Ready to use
• Very easy to roll and brush
• EMICODE EC1 plus: very low emissions

Application area:
weberprim 801 is an alkali-resistant, non-saponifiable primer with dust-binding and water-repellent properties. It can be used to pre-treat absorbent substrates, ideal for subsequent laying of tiles, tile adhesives, screeds, or plasters.
weberprim 801 is suitable for priming gypsum plasters, plasterboard, fiber-reinforced gypsum panels, aerated concrete, mineral plasters, fiber cement panels, concrete, masonry, cement screeds, and calcium sulfate screeds before tile installation. Tile adhesives are protected from rapid water loss, improving their open time and adhesion.

Product description:
weberprim 801 is a single-component, solvent-free primer.

Composition: Plastic dispersion

Product features:

• Improves adhesion to the substrate
• Ready to use
• Very easy to roll and brush
• Alkali-resistant
• Solvent-free

Substrate preparation:
The substrates must be sufficiently load-bearing, dust-free, dry, oil- and grease-free, dimensionally stable, and free of substances that reduce adhesion. Loose or peeling plaster and paint residues must be carefully removed. Peeling plaster and paint residues, lime paints, chalky smear marks, and loose parts must be removed, and surfaces must be dusted. Wash off paint and less resistant dispersion coatings, and ensure they are well dried before treatment.
The necessary substrate pre-treatments should be adapted to the specific conditions of the construction site.

Processing:
weberprim 801 is ready to use or can be diluted up to 1:1 RT with water.
In case of highly absorbent substrates, a double application is required.
Apply evenly and thoroughly with suitable tools such as brushes, rollers, or spray equipment. Avoid foam formation.
Drying should be checked with a scratch or wetness test. After sufficient drying, subsequent covering work can begin. The adhesive application should be completed within 2 days.
Tools should be cleaned immediately after use with water.
In the hardened state, tools can be cleaned with webersys 992.

Material requirement: approximately 150 to 250 ml/m² depending on the substrate.