Remmers Wood Protection Cream, Exterior Area

Remmers Wood Protection Cream for the Protection and Refinement of Wood Outdoors

Translucent pigmented, decorative wood protection glaze for the protection and refinement of wood outdoors

Application Area:

• Exterior wood
• Timber without ground contact according to DIN EN 3351, GK 2 and 3
• Non-structural wooden components: e.g., fences, half-timbered structures, carports, wood cladding
• Limited structural wooden components: e.g., flap covers, profiled boards, garden houses
• Primer, intermediate, and final coating

Properties:

• Only one coat required
• 3-in-1: Impregnation, primer, and glaze
• Protects the wood from moisture and is proactively effective against blue stain fungi
• Reduces the risk of rot when combined with constructive wood protection
• Film protection against mold and algae
• Penetrates deeply
• Breathable
• Brilliant color tones
• Silk-matte finish
• Re-coating without sanding
• Drip-free, suitable for overhead work

Application:

• Material, ambient, and substrate temperature: minimum 5 C to maximum 25 C
• Apply by brush or roller
• Apply in the direction of the grain
• After drying, apply a second coat if necessary
• Seal opened containers well; use as soon as possible
• Test compatibility, adhesion, and color tone on a sample board before application
• When overcoating with other coatings, it is recommended to check adhesion
• White and colorless only for non-exposed exterior surfaces such as roof soffits, or for priming
• For extractive-rich woods such as oak, red cedar, afzelia, redwood, etc., rain may cause leaching of water-soluble wood constituents, which can lead to discoloration on light masonry or plaster
• Seal end grain surfaces in the corresponding color with at least 2 coats
• Cut back the lower end grain surfaces to create a drip edge
• With each glaze application, the color tone intensifies and the gloss increases
• The industry association Deutsche Bauchemie eV provides summarized instructions for handling wood preservatives
• Drying time: approximately 12 hours at 20 C and 65 % relative humidity
• Low temperatures, low air exchange, and high humidity delay drying
• Depending on the wood type, e.g., larch, significant drying delays may occur

Consumption:

Color Number:

• 2715 light oak
• 2716 pine
• 2717 pine/larch
• 2718 walnut
• 2719 teak
• 2720 mahogany
• 2721 white
• 2722 silver gray
• 2723 rosewood

Safety Data Sheet
Data Sheet	Safety Data Sheet PDF
Last revised by the supplier	2010-08-20
Occupational Safety and Storage
Risk Phrases	R20/22 Harmful by inhalation and ingestion R21 Harmful in contact with skin R22 Harmful if swallowed R40 Suspected of carcinogenic effect R41 Risk of serious eye damage R43 Sensitization possible through skin contact R50 Very toxic to aquatic life R50/53 Very toxic to aquatic life, may cause long-term adverse effects in the aquatic environment R51/53 Toxic to aquatic life, may cause long-term adverse effects in the aquatic environment R65 Harmful: may cause lung damage if swallowed R66 Repeated contact may cause cracking or chapping of the skin R67 Vapors can cause drowsiness and dizziness
Hazard Statements	H302 Harmful if swallowed H304 May be fatal if swallowed and enters the respiratory tract H312 Harmful in contact with skin H317 May cause allergic skin reactions H318 Causes serious eye damage H332 Harmful if inhaled H336 May cause drowsiness and dizziness H351 Suspected of causing cancer; specific route of exposure to be provided if confirmed that this hazard exists via another route
Water Hazard Class	2 water hazardous
Hazards
EU Hazard Symbols
GHS Pictograms
Ingredients
CAS Number Absorption Route Substance Name 64742821 64742478 64742945 55406536 60207901 96297