weberdur 137 FaserLeichtputz naturgrau 1mm 30kg

weberdur 137 30kg Fiber Lightweight Render for high thermal insulation of masonry

weberdur 137 is a mineral-based fiber lightweight base coat suitable for interior and exterior use. It is particularly suitable for high thermal insulating masonry with low strength, e.g., lightweight hollow bricks. Thermal conductivity according to 011 W/mK, bulk density less than 700 kg/m³, compressive strength class less than 10, or aerated concrete. Due to its reduced E modulus and fiber reinforcement, weberdur 137 offers a high degree of crack safety. All mineral and organic surface plasters from weber as well as tiles can be applied on weberdur 137. For lesser requirements, weberdur 137 can also be used as an undercoat plaster with an subsequent solvent-free coating in interior areas.

Product Description

weberdur 137 is a factory-produced mineral dry mortar according to DIN EN 998-1.

Composition

Cement, white lime hydrate, organic lightweight aggregates, graded mineral aggregates, additives for better processing, hydrophobizing agents, fibers.

Product Properties

• Low stress, crack-bridging
• High yield
• Fiber-reinforced
• Generally substrate-independent setting behavior
• Particularly suitable for thermal insulating masonry
• Provides maximum safety against crack formation
• Can be processed mechanically and manually

Substrate Preparation

The substrate must be load-bearing, dry, and free of dust and substances that reduce adhesion. Dense substrates, e.g., concrete, require pre-treatment with the mineral bonding bridge weberdur 101 as a groove filler. Observe the curing times after a plaster base treatment. For unsuitable substrates, e.g., deviations from DIN 1053 masonry and DIN 18202 tolerances in high-rise construction, concerns must be addressed, and remedial measures taken. For level and plumb accurate application and termination of plaster profiles, use profile adhesive mortar webermix 125.

Application

Machine Application

The mortar can be processed with all common plastering machines; see equipment planner. By hand, thoroughly mix the contents of a bag with the specified amount of water until a workable consistency is achieved. Apply the mortar in the specified thickness of approximately 10-20 mm. Scratch the freshly applied plaster flat and free of nests. For highly absorbent and/or variably absorbent substrates, work in two layers wet-in-wet. The thickness of the first layer should be about 2/3 of the total plaster thickness. Roughen the surface of the base coat according to the intended top coat, e.g., with a coarse brush or toothed spatula after initial setting. As an undercoat plaster in interior areas, apply 3-4 mm the next day and, after setting, roughen or scratch the surface.

Dimensions

Approx. 1 mm

Color

Natural gray

Application Thickness

10 mm to 20 mm

Water Requirement

Approx. 8 l per 30 kg

Storage

In a dry, moisture-protected storage, the material is storable for up to 1 year.

Safety Data Sheet
Datenblatt	Sicherheitsdatenblatt.pdf
Vom Lieferant überarbeitet am	22.01.2015
Work Safety and Storage
HS-Code	H315 Causes skin irritation
H318	H318 Causes serious eye damage
H335	H335 May cause respiratory irritation
PS	Please observe section 22 of the safety data sheet
Additional Information	P101 If medical advice is needed, keep container or label available P102 Keep out of reach of children P103 Read label before use P280 Wear protective gloves, protective clothing, eye protection, face protection P302+P352 IF ON SKIN: Wash with plenty of water P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. P310 Immediately call a POISON CENTER or doctor P362 Remove contaminated clothing P501 Dispose of contents/container in accordance with local regulations
Hazard Class
Wassergefährdungsklasse	Water hazard class 1, slightly water hazardous
Danger
Signalwort	Danger
GHS Pictogram
GHS Pictogram
Ingredients	CAS Number Intake Route Substance Name 65997-15-1 130562-0