35x webertherm 300 Adhesive and Reinforcement Mortar Gray 30kg

Palette 35 sacks each 30kg webertherm 300 adhesive and reinforcement mortar at an unbeatable price

Mineral, universal adhesive and reinforcement mortar in the webertherm systems A 100, A 200, and B 100 renovation mortars for coating load-bearing plasters

Application area:
Thick-layer mineral adhesive and reinforcement mortar in the webertherm A 100, A 200, B 100, and AK 500/BK 500 thermal insulation composite systems, renovation mortars for coating load-bearing plasters

Product description:
webertherm 300 is a factory-produced, mineral dry mortar

Composition:
Cement, quicklime hydrate, graded mineral additives, fibers, hydrophobizing agent, additives for improved processing and adhesion to the plaster substrate

Product properties:

• characterized by high adhesive strength and excellent processing properties
• is highly machineable and also available as silo material
• In combination with the webertherm reinforcement meshes, a high-performance reinforcement layer is achieved for the webertherm thermal insulation composite systems
• can also be used for coating load-bearing plasters

Color shades: gray
Application thickness: 5 mm – 8 mm
Water requirement: approx. 8 l / 30 kg
Storage: When stored in a dry, moisture-protected environment, the material is storable for up to 1 year

Substrate preparation:

• The substrate must be load-bearing, sufficiently dry, and even
• The flatness of the substrate must meet the requirements of DIN 18 202 "Tolerances in Building Construction"
• Dirt, dust, and loose parts must be removed from the substrate
• Existing old coatings must be removed to at least 70%
• Perform adhesion test on critical substrates

Processing

Processing steps:

• The adhesive and reinforcement mortar is mixed with clean water in the specified amount using a paddle mixer until a workable consistency is achieved. The mortar can also be processed with all common plastering machines and silo mixing pumps, e.g., EMP. For applying the adhesive mortar to the insulation boards, a special adhesive gun can be used.

Bonding:

• The webertherm insulation boards are coated in a frame shape and with two or three vertical strips with adhesive mortar
• The mortar is distributed so that at least 50% of the surface is bonded to the substrate after pressing
• On sufficiently even substrates and when using the webertherm speedy and express insulation boards, the mortar can also be sprayed onto the substrate in a wulst pattern machine. Minimum 50% coverage. The insulation boards are pressed immediately into the mortar. The webertherm insulation boards can also be fully coated with adhesive

Reinforcing:

• The mortar is applied approximately 5 to 8 mm thick onto the insulation boards and troweled flat
• Subsequently, the reinforcement mesh, roughly webertherm 310, is embedded in the reinforcement mortar in vertical or horizontal strips, without folds, using trowels or floats
• The surface is roughened depending on the type of top plaster, e.g., for fine textured plaster or only roughened

Coating of plasters:

• The mortar is applied to the cleaned or appropriately pretreated plaster surfaces up to a maximum of 10 mm and troweled flat
• If cracks are present in the substrate, the reinforcement mesh, roughly webertherm 310, is embedded in the reinforcement mortar in vertical or horizontal strips, without folds
• For thick-layer top plasters, e.g., fine textured plaster, the reinforcement mortar is roughened after setting with a stiff broom; for other top plasters, it is only roughened

Safety Data Sheet
Data sheet	Safety Data Sheet pdf
Reviewed by supplier on	22012015
Occupational safety and storage
GHS hazard statements	H315 Causes skin irritation H318 Causes serious eye damage H335 May cause respiratory irritation
P statements	Please observe section 22 of the safety data sheet P101 If medical advice is needed, keep container or label available P102 Keep out of reach of children P103 Read label before use P280 Wear protective gloves/protective clothing/eye protection/face protection P302P352 IF ON SKIN: Wash with plenty of soap and water P305P351P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. P310 Immediately call a poison center or doctor P362 Take off contaminated clothing P501 Dispose of contents/container in accordance with local regulations
Storage classes	13 Non-combustible solids
Water hazard class	1 slightly water hazardous
Hazards
Signal word	Danger
GHS pictograms
Ingredients
CAS number Basis of intake Substance name 65997151 1305620