ARDEX X 32 Flexible Flooring Mortar 25kg

ARDEX X 32 Flooring Mortar

Coloring and grouting-free installation of natural stone slabs, natural stone tiles, concrete stone slabs, and Cotto tiles indoors and outdoors

ARDEX X 32 is a flexible flooring mortar for coloring and grouting-free installation of natural stone slabs, natural stone tiles, concrete stone slabs, and Cotto tiles. Equipped with ARDURAPID PLUS effect, X 32 can be used indoors and outdoors. The installation can be carried out in thin, medium, and thick bed methods. ARDEX X 32 meets the requirements C2 FTE S1 according to EN 12004 / 12002.

Product Information:

• Coloring and grouting-free installation of natural stone slabs, natural stone tiles, concrete stone, and Cotto tiles
• Walkable / groutable after 3 hours
• Suitable for layer thicknesses of 3 – 30 mm
• For wall and floor surfaces indoors and outdoors
• With ARDURAPID PLUS effect for rapid crystalline water binding

Technical Data:

• Certified according to DIN EN C2 FTE S1
• GISCODE ZP 1 cement-containing product
• Adjusting time approx. 20 min – 30 min
• Flexural strength after 1 day can be 250 N/mm2 / after 7 days can be 400 N/mm2 / after 28 days can be 600 N/mm2
• Compressive strength after 1 day can be 1000 N/mm2 / after 7 days can be 1500 N/mm2 / after 28 days can be 2000 N/mm2
• Storage: In dry rooms, approximately 12 months in the original sealed container
• Walkability at 20°C after approx. 300 hours, then grouting possible
• Suitable for underfloor heating: yes
• Adhesion tensile strength: according to EN 12004 / dry approx. 1.0 – 2.0 N/mm2 / wet approx. 1.0 – 1.5 N/mm2 / warm approx. 1.0 – 2.0 N/mm2 / freeze-thaw cycle approx. 1.0 – 1.5 N/mm2
• Open time approx. 20 min measured on fresh mortar
• Processing time at 20°C approx. 60 min
• Material requirement approx. 330 kg/m2; powder with trowel notch 8 x 8 x 8 mm
• Material requirement approx. 120 kg powder per m2 and mm layer thickness on smooth substrate
• Bulk density approx. 110 kg/l
• Mixing ratio: approx. 800 – 850 g water per 2500 g ARDEX X 32
• For wall: approx. 750 g water per 2500 g ARDEX X 32

Safety Data Sheet
Data Sheet	Sicherheitsdatenblatt pdf
Revised by supplier on	31.05.2019
GHS Link	https://www.gefkomm.de/id/cfd76d711a
Occupational Safety and Storage
GHS hazard statements	H318 Causes serious eye damage
Precautionary statements	Please observe section 22 of the safety data sheet P102 Keep out of reach of children P261 Avoid inhalation of dust/fume/gas/mist/vapors/aerosol P280 Wear protective gloves/protective clothing/eye protection/face protection P302P352 IF ON SKIN: Wash with plenty of water P305P351P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing
Storage classes	13 Non-combustible solids not assigned to any of the above storage classes
Water hazard class	1 slightly water hazardous
Hazards
Signal word	Danger
GHS pictograms
Ingredients
CAS Number Basis for classification Substance name 65997-15-1 7778-19-9