Go to the consent manager Skip to main content Skip to search Skip to navigation Jump to footer
tubag Joint Sealant PFN 25kg
Trass cement-bound joint mortar for natural and concrete stone paving
Information on product safety Manufacturer EU Responsible Person

Color
from 35,90 €
incl. 19% VAT , plus shipping costs
Available immediately

Maximal 1 mal im Paket enthalten
Bag(s)

This item has variations. Please select the requested variation.

Expressversand möglich mit:

Tubag Paving Joint Mortar PFN 25kg

Tubag Paving Joint Mortar PFN 25kg

Hydraulically bound paving joint mortar for natural stone and concrete paving

  • Simple and efficient processing through Easy Clean Technology (ECT)
  • Water-impermeable
  • Compressive strength 25 N/mm2

Application areas

  • Suitable for use in traffic categories N1 and N2 according to ZTV Wegebau
  • For light traffic loads with vehicles up to 35 t
  • For new jointing and restoration
  • For decorative design of terraces, plazas, and paths
  • For the formation of drainage channels

Properties

  • Effectively prevents the risk of lime bloom
  • Good edge adhesion
  • Frost-resistant
  • Low shrinkage
  • Single-component
  • Effectively prevents weed growth in joints

Composition

  • Cement according to DIN EN 1971
  • Trass according to DIN 51043
  • Gradated quartz sands according to DIN EN 13139
  • Additives for controlling and improving processing and product properties

Substrate

Conditioning
  • When paving, the joint depth must be twice the joint width, but at least 30 mm
  • For untrafficked surfaces
  • An exception are ceramic and fine stoneware terrace coverings laid in bonded construction, where the minimum joint depth is approximately 20 mm
  • For trafficked surfaces, the joint depth must be at least two-thirds of the stone height, but at least 40 mm
  • Required minimum joint width 5 mm
  • Maximum joint width 25 mm
Pre-treatment
  • The required joint depth is created by blowing out or chipping out the joints
  • The paving surface must be thoroughly cleaned dry afterwards
  • The paving surface should be pre-wetted multiple times depending on absorption behavior
  • When applying the joint mortar, no water should stand in the joints
Temperature
  • Do not process or let dry at air and material temperatures below 5°C or above 30°C, in direct sunlight, or strong wind

Mixing

Preparation
  • For manual mixing, first pour the specified amount of water into a clean container and add dry mortar
  • Use clean tap water
  • Mix the material with a suitable stirrer until homogeneous and free of lumps, then let it mature briefly and remix
  • Consistency should be slightly flowable
  • For machine processing, adjust water addition to achieve workable consistency
  • Do not mix with other products or foreign substances

Processing

  • The joint filling is done by pressing in with a rubber float
  • Apply the mortar with a rubber trowel under light pressure diagonally across the joint cross-section, ensuring the joints are completely sealed and filled deeply
  • Only minimal amounts should remain on the stone surface to facilitate cleaning
  • For joints with beveled edges, after cleaning, the joint mortar should only fill up to the underside of the bevel
  • Immediately after filling, clean the paving surface
  • Check the surface with a thumb test
  • Mortar residues on the stone surface must not dry out
  • Depending on absorption and surface design, cleaning can be done by:
    • Spraying: Depending on absorption, surface design, and temperature, curing time is approximately 1 to 3 hours. Wash the paving with a water hose and a stiff broom diagonally across the joints, ensuring the mortar is not washed out of the joints. Repeat if necessary until the residual film is completely removed. If needed, remove remaining dirt with a high-pressure cleaner after complete curing.
    • Washing: Depending on absorption and surface design, curing time is approximately 30 to 90 minutes. Wash the surface with a sponge board diagonally across the joints, ensuring the mortar is not washed out. Change wash water regularly. Repeat until the residual film is completely removed. If necessary, remove remaining dirt with a high-pressure cleaner after complete curing.
  • Processing time
    • Approx. 15 minutes
    • Time references are based on 20°C and 65% relative humidity
    • Lower temperatures and high humidity extend processing times; higher temperatures and low humidity shorten them
    • Already stiffened mortar must not be diluted with additional water and processed further

    Drying and curing

    • The fresh mortar must be protected from rapid drying and adverse weather conditions such as frost, drafts, direct sunlight, and heavy rain, possibly by covering with foil
    • The paving surface is walkable after about 3 hours and fully loadable after approximately 28 days
    • Time references are based on 20°C and 65% relative humidity

    Safety Data Sheet

    Sicherheitsdatenblatt PDF
    04.03.2013

    Arbeitsschutz und Lagerung

    H315
    Verursacht Hautreizungen
    H318
    Verursacht schwere Augenschäden
    H335
    Kann die Atemwege reizen

    P101

    Ist ärztlicher Rat erforderlich, Verpackung oder Kennzeichnungsetikett bereithalten

    P102

    Darf nicht in die Hände von Kindern gelangen

    P103

    Lesen Sie sämtliche Anweisungen aufmerksam und befolgen Sie diese

    P261

    Einatmen von Staub, Rauch, Gas, Nebel, Dampf, Aerosol vermeiden

    P271

    Nur im Freien oder in gut belüfteten Räumen verwenden

    P280

    Schutzhandschuhe, Schutzkleidung, Augenschutz, Gesichtsschutz tragen

    P302+P352

    BEI BERÜHRUNG MIT DER HAUT mit viel Wasser waschen

    P304+P340

    BEI EINATMEN die Person an die frische Luft bringen und für ungehinderte Atmung sorgen

    P305+P351+P338

    BEI KONTAKT MIT DEN AUGEN einige Minuten lang behutsam mit Wasser spülen, eventuell vorhandene Kontaktlinsen nach Möglichkeit entfernen, weiter spülen

    P310

    Sofort GIFTINFORMATIONSZENTRUM oder Arzt anrufen

    P332+P313

    Bei Hautreizung ärztlichen Rat einholen, ärztliche Hilfe hinzuziehen

    P362

    Kontaminierte Kleidung ausziehen

    P501

    Inhalt in geeignete Behälter entsorgen

    Lagerklassen

    13
    Nicht brennbare Feststoffe, die keiner der vorgenannten LGK zuzuordnen sind
    1 schwach wassergefährdend

Product safety information
Manufacturer information:
Sievert Baustoffe SE & Co. KG
Mühleneschweg 6
Niedersachsen
Osnabrück, Deutschland, 49090
info@sievert.de
https://www.sievert.de
Responsible person:
Sievert Baustoffe SE & Co. KG
Mühleneschweg 6
Niedersachsen
Osnabrück, Deutschland, 49090
info@sievert.de
https://www.sievert.de
  • Container: Bag
  • Item weight: 25,00 kg
  • Content: 25,00 kg
  • GoogleShopping: Saison

Technisches Datenblatt:

Sicherheitsdatenblatt:

5/5
(1)

4 Stars
3 Stars
2 Stars
1 Star

Share your experiences with other customers!

Topp Service
5 from 5

Jederzeit wieder

T. H. | 01.04.2021 | Verified purchase
Reviews marked as "Verified purchase" were written by customers who verifiably purchased the item from this online shop.
Contact data
All fields marked with * are mandatory.
Question about item

Please see our privacy notice

Others also bought:

Loading ...