ROMPOX® D1 Paver Joint Mortar – Load-Bearing, Weed-Free, Water-Permeable
The ROMPOX® D1 Paver Joint Mortar is the ideal solution for the permanent and low-maintenance jointing of paving surfaces in outdoor areas. As a high-quality 2-component paving joint mortar, it is perfectly suited for heavily trafficked areas such as driveways, courtyards, or parking lots – even with occasional heavy load traffic.
Thanks to its special formulation, the joint mortar for driveways is particularly pressure-resistant and reliably prevents washout of joint material. The mortar is weed-inhibiting and thus minimizes maintenance efforts – for clean surfaces without chemical agents. Additionally, it is water-permeable, effectively preventing dust accumulation and allowing the ground to breathe – environmentally friendly and frost-resistant.
The application is straightforward. The ROMPOX® D1 can be easily worked in and becomes walkable and load-bearing after a short period. Whether for new jointing or renovation – this joint mortar convinces through durability, functionality, and a well-maintained appearance.
Properties of ROMPOX® D1 Paver Joint Mortar
- Suitable for medium traffic loads
- Joint widths from 3 mm
- Joint depths from 30 mm
- Water-permeable
- Self-compacting
- Water-emulsifiable
- Application temperature from 0 °C
Colors
- Stone Gray
- Basalt
- Neutral
Application
Construction Site Requirements
The substrate should be prepared according to the expected traffic load. The regulations and information sheets for the manufacture of paving surfaces must be observed. Excessive loads must not cause settlement of the surface or loose stones. The use of ROMEX® TRASSBETTUNG frost-resistant bedding mortar is ideal.
Preparation
Clean joints to at least 30 mm depth. Minimum joint width 3 mm. The surface to be jointed must be free of dirt of any kind before jointing. Adjacent surfaces not to be jointed should be masked.
Pre-wetting
Pre-wet surfaces. Absorbent surfaces and higher substrate temperatures require more intensive pre-wetting.
Mixing
Pour the 25 kg component of filler fully into the mixer and start mixing. During mixing, slowly add the 25 kg resin-hardener component supplied separately. After 3 minutes of mixing, add water according to the product packaging and mix for at least another 3 minutes. Total mixing time: at least 6 minutes.
Application
Pour the mixed joint mortar onto the well-prepared surface and carefully work it into the joints with a rubber trowel. To optimize the workability, apply the mortar at three to four points within the joint area. Working time: 20 – 30 minutes at 20 °C.
Cleaning
After approximately 10–15 minutes, carefully sweep the surface with a coarse broom and then clean with a fine hair broom until all mortar residues are removed from the surface. The correct time for sweeping is reached when no more white streaks form on the surface. Sweep diagonally across the joints. Do not reuse swept material.
Post-Treatment
The freshly jointed surface should be protected from rain for 12–24 hours. The rain protection must not be placed directly on the surface to allow air circulation. During the initial period, a thin film of synthetic resin remains on the surface, intensifying the color and protecting against dirt. This film disappears over time with weathering and abrasion. In case of doubt, create a sample surface before the full jointing process.
Safety Data Sheet | ||
|---|---|---|
| Sicherheitsdatenblatt.pdf | ||
| 27.11.2007 | ||
Transport Data
| 3082 | |
| UMWELTGEFAHRDENDER STOFF FLÜSSIG NAG | |
| Reaktionsprodukt Bisphenol A Epichlorhydrinharze mit durchschnittlichem Molekulargewicht lt 700 | |
| III | |
| 9 | |
| 3 | |
| 1 |
Extended Transport Data
| 5 L | |
| EQ1 | |
| 2500 kg | |
| Bag | |
| ME |
Hazard
 |
Ingredients
| CAS Number | Absorption Route | Substance Name |
|---|---|---|
| 25068-38-6 | nbspt | |
| 55492-52-9 | nbspt | |
| 26761-44-5 | nbspt | |
| 68609-97-2 | nbspt |
- Container: Bucket
- Item weight: 25,00 kg
- Content: 25,00 kg
- GoogleShopping: Saison
