Go to the consent manager Skip to main content Skip to search Skip to navigation Jump to footer
KNAUF Super Lupp Kalk-Zement-Leichtputz 20kg
Special fast-setting lime-cement lightweight render with fibers and lightweight aggregates
Information on product safety Manufacturer EU Responsible Person

9,90 €
0,49 € per 1 kg
incl. 19% VAT , plus shipping costs
Available immediately
Delivery time: 2 - 3 Workdays (DE - int. shipments may differ)
Bag(s)
KNAUF Super Lupp Kalk-Zement-Leichtputz 20kg
KNAUF Super Lupp Kalk-Zement-Leichtputz 20kg
9,90 € *
0,49 € per 1 kg
0,49 € per 1 kg

Knauf Super Lupp Lime Cement Lightweight Render 20kg

Specially formulated fast-setting lime-cement lightweight render with fibers and lightweight aggregates. Lightweight Render Type II for all standard and high thermal insulation masonry types made of bricks, aerated concrete, Liapor, etc., as well as precast concrete panels and other wall substrates that are still to be overcoated with a top coat.

Pre-treatment is necessary on various substrates.

Properties

  • Lightweight mortar LW, compressive strength category CS II according to DIN 9981
  • Mortar group P II according to DIN V 18550
  • Lightweight Render Type II
  • With EPS aggregate and fiber additive
  • Water-repellent
  • Diffusion-open
  • Weather-resistant
  • Low-stress
  • Primarily for exterior use
  • Suitable for machine or manual application

Application

Suitable for all standard and high thermal insulation masonry types made of bricks, aerated concrete, Liapor, etc., as well as precast concrete panels and other wall substrates that are still to be overcoated with a top coat. Pre-treatment of the substrate is necessary on various surfaces.

As an interior and exterior primer, as well as for small-format tiles (60 x 30 cm) in residential buildings and kitchens.

Execution

Apply Super Lupp to prepared substrate in a minimum thickness of 15 mm, trowel flat, and smooth. For Mak3 as a top coat, apply at least 15 mm of Super Lupp in a full coat, trowel smooth, and then roughen with a coarse trowel. Embed a surface-reinforcing mesh 8x8 mm if needed. Depending on the substrate, ridges and unevenness can be removed after approximately 2 hours with a grid trowel. Conduct a scratch test with the grid trowel.

Super Lupp is a fast-setting material. Spraying interruptions are a maximum of 15 minutes, or up to 25 minutes in warm weather. During longer pauses, clean the mortar and spray equipment. Do not leave the mortar or spray equipment in the sun. Material that has set cannot be processed further.

Preparation

Normal absorbent substrates can be plastered without pre-treatment. On highly absorbent substrates, apply wet-on-wet, with a layer of 5-10 mm first, followed by a second layer up to the required plaster thickness, also wet-on-wet. On non-absorbent substrates, a mineral adhesion bridge with SM700 Pro, SM300 Base, SM or Lustro must be applied.

Application

For pre-treatment of the substrate, allow the applied primer to dry completely. Render is usually processed with a mixing pump, e.g., PFT G4/G5, which is particularly efficient and time-saving. It can also be applied manually with a trowel. Distribute the plaster evenly with a trowel or straightedge and smooth after initial setting, then re-scrape.

Drying

The finished base coat must be completely dry before further coating. The drying time depends on the thickness of the plaster and external conditions such as weather and temperature. To prevent too rapid drying, exterior renders should be protected from direct sunlight. Generally, the minimum drying time is 1 day per mm of plaster thickness.

Safety Data Sheet

Safety Data Sheet

Sicherheitsdatenblatt.pdf
15.04.2015

Arbeitsschutz und Lagerung

H315
Verursacht Hautreizungen
H318
Verursacht schwere Augenschäden
H335
Kann die Atemwege reizen
P102
Darf nicht in die Hände von Kindern gelangen
P261
Einatmen von Staub, Rauch, Gas, Nebel, Dampf, Aerosol vermeiden
P280
Schutzhandschuhe, Schutzkleidung, Augenschutz, Gesichtsschutz, Gehörschutz tragen
P305+P351+P338
BEI KONTAKT MIT DEN AUGEN einige Minuten lang behutsam mit Wasser spülen. Eventuell vorhandene Kontaktlinsen nach Möglichkeit entfernen. Weiter spülen.
P310
Sofort GIFTINFORMATIONSZENTRUM, Arzt anrufen
P501
Inhalt/Behälter gemäß örtlichen Vorschriften entsorgen

Lagerklassen

1 schwach wassergefährdend

Gefahren

Gefahr
Ätzend Reizend
GHS05 Ätzend Reizend
Gesundheitsgefaumlhrdend
GHS07 Gesundheitsgefährdend

Product safety information
Manufacturer information:
Knauf Gips KG
Am Bahnhof 7
Baden-Württemberg
Iphofen, Deutschland, 97346
info@knauf.de
https://www.knauf.de
Responsible person:
Knauf Gips KG
Am Bahnhof 7
Baden-Württemberg
Iphofen, Deutschland, 97346
info@knauf.de
https://www.knauf.de
  • Container: Bag
  • Item weight: 20,00 kg
  • Content: 20,00 kg
  • GoogleShopping: Prio-Artikel

Sicherheitsdatenblatt:

Write the first review for this item and help others make a purchase decision!:

Contact data
All fields marked with * are mandatory.
Question about item

Please see our privacy notice

Others also bought:

PCI Pecitape 120 Object Sealant Tape 10 m
26,90 € *
2,69 € per 1 m
Loading ...