PCI Nanocret R2 Lightweight Repair Mortar 20 kg

PCI Nanocret R2 Light Repair Mortar Universal for Concrete Components and Masonry

Product Properties

• Waterproof, weather- and frost-resistant
• Universal indoor and outdoor use
• Becomes plastic and pliable after water addition, easy to process
• Rapid work cycle, reworkable after approximately 4 hours
• Adheres securely to concrete, screed, and masonry
• High stability, ideal for reprofiling and modeling work
• Lightweight mortar technology
• Low modulus of elasticity
• Certified according to EN 15043 R2
• Listed as repair mortar R2 XF4 according to ÖBV

Color: gray

Packaging: 20 kg bag

Application Area

• For indoor and outdoor use
• For floors, walls, and ceilings
• Reprofiling of corners and edges of concrete components
• Filling of chasms and holes in screeds, concrete ceilings, staircases, and balcony slabs
• Filling of pipe trenches in concrete walls, hollow spaces between concrete and steel frames, among others
• To level uneven concrete substrates in swimming pools
• To spackle and level masonry
• To level stair treads
• For reprofiling work
• Can be used as a fillet filler
• Can be used as a surface filler
• Layer thickness: approximately 3 – 30 mm for chasms, 3 – 100 mm

Substrate Preparation

• Minimum substrate age:
• PCI Novoment M1 plus and PCI Novoment Z1: 24 hours
• PCI Novoment M3 plus and PCI Novoment Z3: 3 days
• Cement screed: 28 days
• Concrete: 3 months
• The substrate must be dry, free of dust, and load-bearing
• Strongly absorbent cement substrates should be primed with PCI Gisogrund 1 diluted with water 1:1
• Sandpapered anhydrite or gypsum screeds and cast asphalt screeds should be primed with PCI Gisogrund undiluted
• For time-sensitive work, cementitious and gypsum-containing substrates should be primed with PCI Gisogrund Rapid and allowed to dry
• Zement screeds should not exceed 4% residual moisture content; anhydrite screeds should not exceed 0.5%, measured with a CM device

Substrate Preparation

• The substrate must be clean, load-bearing, free of dust and grease
• Remove loose parts and cement laitance
• Smooth concrete surfaces should be roughened until the aggregate is visible
• The substrate may be moist but not wet
• Clean surfaces contaminated with grease and oil with PCI Entoumlmmer
• Pre-treated substrate should be sufficiently moist and matt during application, at least 2 hours prior, and kept moist; surface must be matte and moist, avoiding foam formation

Processing PCI Nanocret R2

• Pour water into a clean mixing container, add the appropriate amount of PCI Nanocret R2, and mix with a suitable stirring or mixing tool, e.g., a Collomix attachment on a powerful drill, until a plastic, lump-free mortar is formed
• Let it rest for 2 minutes, then stir again
• First, apply a scratch coat of the mixed mortar onto the prepared, matte-moist substrate or alternatively prepare a bonding slurry from PCI Nanocret R2 with a good spreading consistency and apply with a broom or trowel
• The subsequent application is then done wet-on-wet in the desired layer thickness between 3 and 100 mm
• For surface application, work in multiple layers starting from 30 mm thickness
• Once the mortar has set, approximately 30 – 60 minutes after application at 20°C, finishing can begin with rubbing, e.g., with a sponge or wooden/plastic board
• In strong wind or direct sunlight, the finished surface should be kept moist or covered with foil during the first 4 hours to prevent rapid drying

Cleaning

• Tools should be cleaned immediately after use with water; once hardened, only mechanical removal is possible

Important Notes

• Do not dilute setting mortar with water or mix with fresh mortar once it begins to set

Safety Data Sheet

Safety Data Sheet
Datenblatt	https://bauschnell.de/Hersteller/PCISDB/NanocretR2.pdf
Revised by supplier on	21.11.2016
GHS Signal Word	Gefahr
GHS Pictogram
Ingredients
CAS Number Basis for Assessment Substance Name 65997-15-1