PCI Nanofug Premium, 19,90 €

PCI Nanofug Premium Variable Flexible Joint Filler 5kg for all ceramic tiles, glass mosaics, glass tiles, and all natural stones

Product features

Very easy to clean thanks to the easy to clean effect
Reduced resistance to acids from household cleaners
Enhanced protection against certain molds and microorganisms
High processing comfort with an application window of approximately 40 minutes
Rapid setting but no burning
Fine surface finish and brilliant color rendition
Meets CG2 WA according to DIN 13888:2009
Low emissions GEV EMICODE EC1 Plus

Colors

Nr 16 silbergrau
Nr 19 basalt
Nr 21 hellgrau
Nr 22 sandgrau
Nr 31 zementgrau
Nr 47 anthrazit
Nr 02 bahamabeige
Nr 03 caramel
Nr 05 mittelbraun
Nr 11 jasmin
Nr 12 anemone
Nr 18 manhattan
Nr 20 weiszlig
Nr 23 lichtgrau
Nr 27 jurabeige
Nr 40 schwarz
Nr 41 dunkelbraun
Nr 43 pergamon
Nr 44 topas
Nr 49 hellbraun
Nr 50 rotbraun
Nr 51 intensivbraun
Nr 52 beigebraun
Nr 53 ocker

Delivery form

5kg bucket

Application area

For indoor and outdoor use
For wall and floor joints
For joint widths of 1 – 10 mm
Suitable for all ceramic tiles, glass mosaics, glass tiles, and all natural stones
Suitable for living areas in buildings, showers, balconies, terraces, facades, and in public and commercial areas with high moisture exposure, e.g., shower installations, saunas, toilet facilities, sales and presentation areas
On heated screeds, dry screeds, concrete prefabricates, plasterboard, plasterboards, wood chipboards, wooden floors, and in areas with significant temperature fluctuations

Substrate preparation

Immediately after laying the tiles, scrape the joints evenly and deeply to the tile thickness and clean
Allow the adhesive or laying mortar to mature

Processing PCI Nanofug Premium

Mixing water: see mixing ratio in a clean container
Add PCI Nanofug Premium and immediately knead to a homogeneous, lump-free mortar using a suitable stirring or mixing tool, e.g., from Collomix as an attachment to a drill
After about 3 minutes, knead again
Apply the joint mortar with PCI rubber jointing disc into the joints and allow to set
If necessary, rework with PCI Nanofug Premium thoroughly
After sufficient setting, wash off with a slightly damp, stable sponge or sponge board
After drying, remove any remaining mortar residue with a slightly damp sponge

Important notes

Do not process at substrate temperatures below 5°C or above 25°C, or in direct sunlight or drafts
Lower temperatures shorten, higher temperatures extend processing time
Protect freshly jointed surfaces from sunlight and strong drafts
During jointing and curing, at least 24 hours must pass, and any underfloor heating must be switched off
If a white film remains on the ceramic surface after drying, it can be removed after 2 to 3 days with a cement film remover. Thoroughly clean the joints and surface beforehand and rinse thoroughly with plenty of water afterwards
In case of intensive use, salt-containing cleaners or prolonged exposure to cement-aggressive media can attack the joint. Clean the joints thoroughly before cleaning and rinse with plenty of water
When jointing slip-resistant or textured floors, residual film must be carefully removed while still fresh. Conduct a test joint or cleaning first
For polished fine stoneware, color pigments can settle in the micro-pores of the surface. Avoid strong color contrast between tile and joint. Conduct a test joint if in doubt
When jointing sharply edged tiles, it is recommended to use the joint fleece, see brochure "Work and advertising material for the tiler trade"
For black color, increased cleaning effort is expected
Before jointing, secure edge and movement joints by inserting styrofoam strips or foam profiles. Remove protective strips before elastic jointing. For joints between tiles, fixtures, and pipe penetrations, as well as corner and connection joints, use PCI Silcofug E or PCI Silcoferm S elastically on facades with PCI Elritan 100
Use only joint mortar with the same batch number on the same object
Mixing PCI Nanofug Premium with quartz sand can alter the original color tone

Safety Data Sheet

Safety Data Sheet
Datenblatt	Sicherheitsdatenblatt PDF
Vom Lieferant überarbeitet am	08.06.2017
Work safety and storage
GHS symbol	H315 Causes skin irritation
H318	H318 Causes serious eye damage
H335	H335 May cause respiratory irritation
Precautionary statements	P102 Keep out of reach of children P261 Avoid inhalation of dust, fumes, gas, mist, vapor, aerosol P264 Wash thoroughly after handling P280 Wear protective gloves, protective clothing, eye protection, face protection P302+P352 IF ON SKIN: Wash with plenty of water P304+P340 IF INHALED: Bring the person into fresh air and ensure unrestricted breathing P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing P315 Seek medical advice immediately P332+P313 If skin irritation occurs: seek medical advice P362+P364 Remove contaminated clothing and wash before reuse P501 Dispose of contents/container in accordance with local regulations