Go to the consent manager Skip to main content Skip to search Skip to navigation Jump to footer
<li>webertec 946 Injection Cream 10 l Bucket</li> <li>GLORIA Pressure Sprayer 5 Liter</li>

For the subsequent horizontal waterproofing of masonry against rising damp

Mit dem Bauschnell ChatGPT Assistent chatten

Information on product safety Manufacturer EU Responsible Person

Contents
566,99 €
56,70 € per 1 l
incl. 19% VAT , plus shipping costs
Available immediately
Delivery time: 2 - 3 Workdays (DE - int. shipments may differ)
Bucket(s)
gelbes gloria prima 5 drucksprühgerät 5 l mit...
<li>webertec 946 Injection Cream 10 l Bucket</li> <li>GLORIA Pressure Sprayer 5 Liter</li>
566,99 € *
56,70 € per 1 l
56,70 € per 1 l

weberTec 946 Silane-Based Injection Cream for the Retrofitting Horizontal Sealing of Masonry Against Rising Moisture

Silane-based injection cream for the retrofitting horizontal sealing of masonry against rising moisture

Application Area:
For the retrofitting cross-section sealing of masonry against rising moisture using the non-pressurized drill hole injection method in cases of moisture levels up to 95 % in the masonry. Suitable for all common masonry types.

Product Description:
webertec 946 is a watery, solvent-free injection cream based on silane with official test certificate according to WTAMerkblatt 4404.

Color: white;
Storage: When stored dry and frost-free in the original sealed container, the material remains usable for at least 12 months.

Composition:
Silane base

Product Properties:

  • Ready for use
  • Especially suitable for cavity masonry, no uncontrolled runoff
  • Simple and safe to apply
  • Application with hand pressure sprayer or e.g., Gloriaspritze
  • Effective even at high moisture levels up to 95 %
  • Watery cream penetrates into the finest capillaries
  • Does not form harmful salts in the building material


General Notes:
Drying of the walls above the injection zone to the equilibrium moisture content can only occur if no dense wall coatings are present. Remove plasters and paints and ensure adequate drying conditions in the treated room spaces.
Additional measures may be necessary. It must be ensured that at least one joint is drilled through. For masonry thicknesses over 60 cm, we recommend pressure injection with webertec 940 E. In wall corners, drill holes on both sides.
Depending on the extent of damage, flank measures such as retrofitting or interior sealing or repair plaster systems should be used. The notes of WTA Merkblatt 4404 Masonry Injection must be observed.

Special Notes:

  • Do not mix with other building materials
  • The application tip "How to properly carry out basement interior renovation" must be observed
  • Not suitable for aerated concrete


Substrate Preparation:

  • Old, crumbly, and poorly adhering plasters and coatings must be removed down to load-bearing substrate. Masonry joints approximately 2 cm deep should be chiseled out and the surface mechanically cleaned.
  • Damaged masonry should be replaced or supplemented. Substrate preparation is carried out at least 0.8 m beyond the moisture damage area.
  • For interior walls or vaulted ceilings, the substrate pre-treatment extends at least 1 m from the outer wall.
  • Drill holes with a diameter of approximately 16 mm at a spacing of about 8 to 12 cm, preferably horizontally, into the mortar joint. The drill hole depth corresponds to the wall thickness minus 5 cm.
  • If the drill holes are to be sealed afterwards, drill into the masonry joint or brick at an angle up to 45°. The bore must reach within about 5 cm of the outer wall surface.
  • For high moisture levels (>75 %), drilling in two staggered rows is recommended.
  • Blow out drill holes with oil-free compressed air.
  • In two-row arrangements, do not exceed an offset of 8 cm.


Application:

  • Injection method
  • Insert webertec 946 bag into the prepared webersys hand pressure sprayer No. 3. Screw the adapter firmly onto the hose thread. Attach the injection tube securely to the adapter shaft.
  • Alternatively, use suitable dispensing equipment, e.g., Gloriaspritze with injection lance.
  • Injection begins pressureless from the bottom row of drill holes. Each drill hole must be completely filled with injection cream from the back to the front.
  • After the injection material has been fully absorbed, fill the drill holes with webertec 942 or seal with webertec 933.

Safety Data Sheet

Safety Data Sheet PDF
2012-2016

Occupational Safety and Storage

10
Flammable liquids, flash point > 60°C
1 Slightly water hazardous

  • Container: Bucket
  • Item weight: 12,30 kg
  • Content: 10,00 l
  • GoogleShopping: Hauptsortiment

Technisches Datenblatt:

Sicherheitsdatenblatt:

Write the first review for this item and help others make a purchase decision!:

Contact data
All fields marked with * are mandatory.
Question about item

Please see our privacy notice

Others also bought:

webertec 946 Injection Cream 10 l
409,90 € *
40,99 € per 1 l
webertec 933 Hohlkehlenspachtel 25KG
45,70 € *
1,83 € per 1 kg
webertec Superflex D2 Flex Sealant 2K 24kg
129,90 € *
5,41 € per 1 kg
Loading ...