PCI Pavifix CEM Rapid 25kg Cement Paving Joint Mortar

PCI Pavifixreg CEM Rapid Cement Joint Mortar for Natural Stone Slabs and Natural Stone Paving

MHD 04/2025 Product from return and warranty exclusion

Product features

• Light flowable, full filling of joints
• Highly resistant to wear, durable, resistant to weathering and mechanical stress, e.g., by sweeping machines
• Rissfrei, the joint does not tear or break out
• Fast setting
• Water-impermeable
• Frost and thaw resistant
• Suitable for processing in the Gieszlig method when laying slabs
• Suitable for processing in the Schlämm method for paving surfaces
• Resistant to high-pressure cleaner loads up to 120 bar

Colors: gray, brown Delivery forms: 25 kg bag

Application areas

• For building construction
• For indoor and outdoor use
• For joint widths from 5 to 80 mm
• Especially suitable for jointing natural stone slabs, e.g., polygonal slabs on terraces and garden paths
• Application in the Gieszlig method
• For jointing mosaics, small and large paving made of colorfast natural stone in bonded construction
• Application in the Schlämm method
• Also suitable for application on surfaces with high residual moisture

Preparation of the substrate

The entire structure of the traffic surface and paving must be designed according to the expected load according to RStO. In general, the bonded construction method should be preferred. The following regulations and information sheets apply for paving fixing with paving and slab laying:

• RStO - Guidelines for the standardization of traffic surfaces
• Information sheet DNV "Paving covers and slab laying of natural stone for traffic surfaces"

Bring the joints to the required joint depth evenly before jointing with paving or slabs. In the case of old paving renovation, blow out the joints to the required depth and remove dirt from the stone edges. Allow the joint or laying mortar to mature. In the Schlämm method, pre-wet the surface, ensuring no water remains in the joints to avoid foam formation.

Processing of PCI Pavifix CEM Rapid

• Pour the mixing water into a clean container. Add the powder and mix with a suitable stir or mixing tool attached to a powerful drill, paddle mixer, free-fall mixer, or forced mixer to produce a cohesive, lump-free mortar.
• After a maturation time of approx. 3 minutes, stir again.

Jointing

• In the Gieszlig method, apply the mortar with a suitable Gieszlig container into the joints until a slight excess is achieved. After the mortar has set, test with your fingertip, cut off excess with a trowel, and immediately smooth the joint with a slightly dampened sponge or sponge board. Remove any remaining mortar film from the surface with a sponge or sponge board.
• In the Schlämm method, apply the mixed material onto the pre-wetted surface and work into the joints with a rubber squeegee. Keep the surface moist with a light spray of water. After the mortar has set, test with your fingertip, loosen the mortar residues on the stone surface with water and a rubber squeegee or soft broom (e.g., coconut broom), then rinse the surface with water. To prevent joint filling, the water jet should be directed nearly horizontally to the surface.

Safety Data Sheet
Datenblatt	Sicherheitsdatenblatt.pdf
Vom Lieferant überarbeitet am	04.04.2014
Workplace Safety and Storage
Risiko
Reizt die Atmungsorgane
Reizt die Haut
Gefahr ernster Augenschäden
HS
Verursacht Hautreizungen
Verursacht schwere Augenschäden
Kann die Atemwege reizen
GHS
Verursacht Hautreizungen
Verursacht schwere Augenschäden
Kann die Atemwege reizen
Bitte Abschnitt 22 des Sicherheitsdatenblattes beachten
Wassergefährdungsklasse	1 schwach wassergefährdend

Gefahren

Signalwort	Gefahr
GHS Gefahrensymbole
GHS Piktogramme
Gesundheitsgefahren

Inhaltsstoffe

CAS-Nummer	Aufnahmegrund	Stoffname
65997-15-1		nbspt