weberrep 760 Universal Fast-Setting Cement for Assembly, Plaster, Mortar, and Waterproofing Work
Application Area:
weberrep 760 is a particularly versatile fast-setting cement for concrete precast parts, artificial stone, plaster, screed, or masonry. Ideal for quickly sealing holes, for fixing cladding, heating elements, etc. Suitable for sealing seepage points in cellars, tunnels, shaft linings, and more.
Product Description:
weberrep 760 is a fast-setting additive compatible with all cements according to EN 197.
Composition:
Inorganic binder combination, fillers, additives
Product Properties:
- Versatile use
- Very high early and final strength
- No efflorescence
- Suitable for indoor and outdoor use
- Early load-bearing capacity
- Walkable after approximately 30 minutes
Technical Data:
Processing temperature > 1°C
Flexural strength after 28 days: 10.4 N/mm
Flexural strength after 1 day: 10.1 N/mm
Compressive strength after 60 min: 15 N/mm
Compressive strength after 1 day: 40.3 N/mm
Compressive strength after 28 days: 54.1 N/mm
Powder bulk density: approx. 1.3 kg/dm
Processing time: 3 min to 8 min depending on temperature
Substrate Preparation:
Clean, absorbent, sufficiently load-bearing, free of loose parts, generally pre-wet
Application
Mixing Process
Mixing ratio, depending on required consistency, 2 to 3 RT weberrep 760 and 1 RT water
The material must be mixed quickly. Adjust the mixing amount to the processing time of 8 minutes. Provide the appropriate amount of water during mixing. At temperatures below 5°C, it is recommended to prepare the product with warm water to prevent rapid hardening.
Sealing of Seepage Points
Mix 3 RT weberrep 760 with 1 RT water to form a plastic to stiff mortar. Excavate the damage site as deep as possible, in a swallowtail shape, and press the mortar in with a trowel. The pressure of the trowel must be maintained until the mortar has set.
Creating Moulds
Mix 2 RT weberrep 760 with 1 RT water to produce a thin-flowing moulding compound.
Repair of Concrete and Precast Concrete Elements
Mix 2 to 3 RT weberrep 760 with 1 to 3 RT sharp sand and water to form a plastic mortar. Finally, apply the repair mortar.
Application of cement plasters on moist, non-absorbent substrates
Add approximately 15 to 20 wt% of weberrep 760 to the fully mixed plaster mortar. This ensures immediate stability and increased water impermeability.
Consumption / Yield
Depending on application: 0.8 to 1.8 kg/dm
Product Details
Application tool: Trowel
Color: Cement gray
Water requirement: Depending on desired consistency
Drying time: Depending on use, 12 minutes to 24 hours
Storage: When stored dry in the original sealed container, the material remains usable for at least 9 months
Safety Data Sheet | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Safety Data Sheet PDF | |||||||||||||
| 01/08/2015 | |||||||||||||
Work Safety and Storage | |||||||||||||
H315 Causes skin irritation H318 Causes serious eye damage H335 May cause respiratory irritation | |||||||||||||
P101 If medical advice is needed, keep container or label available P102 Keep out of reach of children P103 Read label before use P280 Wear protective gloves, protective clothing, eye protection, face protection P302/P352 IF ON SKIN: Wash with plenty of water P305/P351/P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. P310 Immediately call a poison center/doctor P362 Take off contaminated clothing P501 Dispose of contents/container in accordance with local regulations | |||||||||||||
13 Non-combustible solids | |||||||||||||
| 1 Slightly water hazardous | |||||||||||||
Hazards | |||||||||||||
| Danger | |||||||||||||
  | |||||||||||||
Ingredients | |||||||||||||
| |||||||||||||
